AUTEL MaxiSys Elite perform Mercedes Benz ME97 SCN Coding

The Autel Maxisys Elite rapidly performs every job from comprehensive vehicle diagnostics & analysis to advanced ECU programming. 2x faster than any comparable device, the Autel MaxiSys Elite provides extended battery life and intelligent power saving. The MaxiSys Elite offers a super-sensitive capacitive screen able to respond to gloved, moistened, and even greasy fingers! The ergonomically angled docking station provides optimum visibility and convenient charging that eliminates power concerns.

AUTEL MaxiSys Elite perform Mercedes Benz ME97 SCN Coding

Autel-MaxiSys-Elite-scanner-1 Autel-MaxiSys-Elite-scanner-2 Autel-MaxiSys-Elite-scanner-3 Autel-MaxiSys-Elite-scanner-4 Autel-MaxiSys-Elite-scanner-5 Autel-MaxiSys-Elite-scanner-6
Autel-MaxiSys-Elite-scanner-7 Autel-MaxiSys-Elite-scanner-8 Autel-MaxiSys-Elite-scanner-10 Autel-MaxiSys-Elite-scanner-11 Autel-MaxiSys-Elite-scanner-12

How to get GM TECH2 CANdi module to work

The Candi Module should not plugged into your GM Tech 2 unless you’re working on a later car ..generally 2005 plus. Olders car from 96 should NOT have the Candi Module attached.

OBD I only has 1 ground, so 12 pin adapter connects signal and chassis ground to the Tech 2 cable.

OBD II has chassis and signal ground and they are connected in the cars wiring.

How I was trying to get GM TECH2 CANdi module to work:
Nothing on CANdi end of cable.
tech2-candi-module-to-work-1

Boot screen not showing CANdi present, diagnostics for CANdi says it isn’t seen.
tech2-candi-module-to-work-2

Here I connected OBD I adapter to end of CANdi cable:
OBD I adapter connected.

CANdi module shows up at boot screen.
tech2-candi-module-to-work-3

Green LED flashes about once every second.
tech2-candi-module-to-work-5

Diagnostic screens for CANdi now present. Hit ENTER, 4, 7 to get to this screen.
tech2-candi-module-to-work-6

POST Results.
tech2-candi-module-to-work-7

Self Test Results.
The weird looking screen is because I have not removed the protective plastic yet.
tech2-candi-module-to-work-8

MaxiSys MS908S Pro Russian Version

autel-MS908SP-8

One of the Maxisys series devices, the MS908S Pro Diagnostic Platform bases on the revolutionary Android multitasking operating system, utilizes the powerful Cortex A7+A15 six-core processor, and equips with 9.7-inch LED capacitive touch screen. Supporting J2534 ECU Programming Device is capable of replacing the existing software/firmware in the Electronic Control Units (ECU), programming new ECUs and fixing software-controlled drivability issues and emission issues. MS908S Pro is an ideal tool for a truly trouble-free diagnosis of a maintenance plant by quickly, efficiently and effectively diagnosing automotive faults, managing customer data, and standardizing business processes.

autel-MS908SP-9

Extraordinarily powerful Cortex A7+A15 six-core processor
9.7” 1024×768 LED-backlit glossy Multi-Touch capacitive display with IPS technology
Internal reliable 64GB On-board Memory for better performance
Built-in 8-megapixel rear camera with autofocus and flashlight
The VCI connects to the main unit wirelessly with up to 70 meters working range
802.11 a/b/g/n/ac Wi-Fi to access your favorite web resources
Unique ergonomic design with rubberized outer protection and a rugged internal housing
Open source Android Operating System for fast boot-up and multitasking
Extensive vehicle coverage for more than 80 US, Asian and European vehicle makes
Exceptional OE-Level system coverage for all electronic systems
Complete capabilities for codes, live data, active test, ECU information, adaptation, matching, etc
Cloud-based Data Manager saves customer and vehicle records, scanner data and technician notes
Built-in rechargeable lithium-polymer battery for up to 7.5 hours of continuous operation
Equip with J2534 ECU Programming Device for replacing the existing software/firmware in the Electronic Control Units (ECU), programming new ECUs and fixing software-controlled drivability issues and emission issues

Does Autel MaxiSys Pro MS908SP Suit You?
This diagnostic device is mainly for professionals, those with Garage or Auto Repairing Shops.
It wouldn’t suit you if you are a single car owner. The design is meant to serve many people.
If you are an owner of a garage or car shop Autel Professional OBD2 MS908P, it could be of great help to you in getting things done fast.

Is It Worth Buying Then?
Autel Maxisys Pro MS908P on OBD2TOOL is an all-around and powerful tool that I would definitely recommend to any professional mechanics in the auto-repairing business.
It can a long way in easing up and increasing efficiency in your engine diagnostics from all the features mentioned. The returns are a guarantee.

Handing over Autel MaxiSys MS906 garage Bui Hien in Binh Duong

AUTEL has delivered Autel MaxiSYS 906 diagnostic technology for Bui Hien garage in Thuan An, Binh Duong. On September 27th, Binh Duong province to transfer the diagnostic technology MS906 for Mr. Hien’s garage. Thank you for your trust and choice of car diagnostics machine by AUTEL. Here are some photos handed Autel MaxiSys MS906 at Bui Hien garage:

Delivering Autel MaxiSys MS906 in Binh Duong

36-1 36-2
36-3

AUTEL technician instructs customers to use the machine, KIA SEDONA test drive is available at the garage

36-4
36-5

The process of guiding customers to use the Autel MaxiSys MS906 error reader

Thank gary Bui Hien has used the diagnostic line of AUTEL, Obd2tool.com wish you abundant health, work growing and constantly reaching out.

Autel MaxiSYS Elite

With more than 50 manufacturers included and access to special functions, activation and coding across more modules, the Autel Maxisys Elite means technicians and shops can execute repairs in house.

With more than 50 manufacturers included and access to special functions, activation and coding across more modules, the MaxiSYS Elite means technicians and shops can execute repairs in house.
The Autel MaxiSYS Elite is the latest addition to Autel’s MaxiSys family of diagnostic tools. The Elite features a faster processor, higher screen resolution, faster Wi-Fi, longer battery life and Android’s 4.3 operating system, compared to the company’s previous products. The Elite’s VCI (Vehicle Communications Interface) utilizes Autel’s J2534 interface for expansion. The Elite includes an all-new docking station which holds the Elite at an optimal viewing angle while charging it conveniently on a toolbox or cart. With the Elite, technicians receive two years of updates and warranty and have access to a dedicated Elite tech support team for faster response.

The Autel MaxiSYS Elite is the latest addition to Autel’s MaxiSys family of diagnostic tools. The Elite features a faster processor, higher screen resolution, faster Wi-Fi, longer battery life and Android’s 4.3 operating system, compared to the company’s previous products. The Elite’s VCI (Vehicle Communications Interface) utilizes Autel’s J2534 interface for expansion. The Autel OBD2 Scanner Elite includes an all-new docking station which holds the Elite at an optimal viewing angle while charging it conveniently on a toolbox or cart. With the Elite, technicians receive two years of updates and warranty and have access to a dedicated Elite tech support team for faster response.

Application
With more than 50 manufacturers (domestic, Asian and European) included and access to special functions, activation and coding across more modules (up to 40 on many makes), the MaxiSYS Elite means technicians and shops can execute repairs in house. More than just drivability and ABS or SRS, they will have access to functions and repairs usually thought of has “dealer only” including immobilizer, information and communication modules, ECU resets and many more.

Selling Points
The Elite is available only through a select group of Autel’s distribution partners. As part of Autel’s MaxiSYS family, it is one of the most frequently asked for by name diagnostic products in the market.

The Elite is thinner and even more ergonomic then other MaxiSYS tools, so if feels and looks great in the technicians hand. Its high-resolution screen will draw the technician to it while sitting in the new charging cradle.

Features and benefits         
A faster processor and newer Android system put the Elite on the cutting edge for diagnostic tools. Its quick boot-time and easy-to-use interface will have technicians into the car’s systems even faster and easier than before.
It includes Autel’s sophisticated J2534 interface module for a wireless Bluetooth connection to the car. This also gives them access to a device for reflashing vehicles.
Once connected to a network, daily updates are easily downloaded.
The Elite has Autel’s OE-styled software giving technicians access to more modules and more functions in those modules to do complete diagnosis and repairs.
Now even longer warranty and free updates every two years versus one.

Manufacturing Specifications
The Elite features a 1.8 GB quad core processor running Android’s 4.3 Jelly Bean system.
Its 2048 by 1536 resolution Retina display is twice the sharpness of its predecessor.
It is capable of up to 10 Ghz Wi-Fi speeds.
The Elite uses the latest 3.0 USB connectivity.
13600 mAH Li-ion battery.

Storage and Display
The Elite from www.obd2tool.com comes with its own docking station for charging and storage. It makes a great display on a truck and gives the technician an easy-to-view charging stand for his toolbox or cart.

Autel Software update Instructions

(Suitable for Autel Scanner MaxiDiag Elite, MaxiCheck ,TS501, TS601, AL609, AL619, EBS301,OLS301, VAG505, MOT PRO)

Register the Tool:

Please go to our website www.autel.com to register an Autel ID.
Then sign in our website with your Autel ID and password to register your tool: http://pro.auteltech.com/

22-1

Note: when registering the tool on our website, please make sure that the serial number and register password that you input are correct.

On the tool itself, you can press on Setup->About to double check the serial number and register password. If you only have the S/N, please contact our technical support to check out the register password.

Update via Computer:
1. Log in our website with your Autel ID and password, and then download the latest PC Suite for your tool from your account. http://pro.auteltech.com/

22-2

2. Then please install the PC Suite on a Windows computer that can get Internet access.

3. Insert the SD card to USB port of the computer via a SD card reader, run the PC Suit, then input your OBD2 Scanner Autel ID and password to log in our system. If you forget your password unintentionally, you may always click the [Forget Password?] to link to our website and reset your password.

22-3

4. Then wait for the Update window to display.
You can use the pull-down menu on the right corner to select the correct SD card if two or more SD cards have been connected to the PC. And you can click on the Install button to download the software updates.
To ensure the good performance of the scan tool, it is recommended to download and install all the software updates.

22-4
6. After downloading all the software, please insert the SD card back to the tool; then you can enjoy the new software.

Getting Started of the MS906

1. Powering Up

Press the Lock/Power button on the top right side of the display tablet to switch the unit on. The system boots up, and shows the lock screen. Press and drag the inner ring to the edge of the circle to unlock the screen; the Autel MaxiSYS MS906 Job Menu is shown.

10-1

1.    Application Buttons
2.    Locator and Navigation Buttons
3.    Status Icons

NOTE: The screen is locked by default when you first turn on the display tablet. It is recommended to lock the screen to protect information in the system and reduce battery usage.

Almost all operations on the display tablet are controlled through the touch screen. The touch screen navigation is menu driven, which allows you to quickly locate the test procedure, or data that you need, through a s eries of choices and questions. Detailed descriptions of the menu structures are found in the chapters for the various applications.

1.1 Application Buttons

The Application buttons configure the Maxisys for the type of operation or activity to be performed. The table below gives brief descriptions of the available applications.
Use your finger tip to select an application from the Job Menu.

10-2
10-3

1.2 Locator and Navigation Buttons

10-4
10-5
To use the camera:
1.    Tap the Camera button. The camera screen opens.
2.    Focus the image to be captured in the view finder.
3.    Tap the inner blue circle. The view finder now shows the captured picture and auto-saves the taken photo.
4.    Tap the thumbnail image on the top right corner of the screen to view the stored image.
5.    Tap the Back or Home button to exit the camera application.

1.3 System Status Icons

These are the standard status icons of the Android operating system. Your display tablet is a fully functional Android Pad. Refer to Android documentation for additional information.
By tapping on this area (bottom right corner), a S hortcuts Panel will be displayed, on which you are allowed to set various system settings of the tablet. Operations of each button on the panel are described in the table below:

10-6

2. Powering Down

All vehicle communications must be terminated before shutting down the display tablet. A warning message displays if you attempt to shut down while the display tablet is communicating with the vehicle. Forcing a shut down while communicating may lead to ECM problems on some vehicles. Exit the Diagnostics application before powering down.

To power down the display tablet:
1.    Press and hold the Lock/Power Button.
2.    Tap Power off option.
3.    Tap OK; the tablet will turn off in a few seconds.

2.1 Reboot System

In case of system crash, press and hold the Lock/Power button for 8 seconds to reboot the system.

3 Installing Computer Software

The MaxiSys Diagnostic Platform allows you to realize some of its functions on a c omputer to enhance capabilities and i mprove user experience. To realize these functions on a computer, you need to install certain software.
There are two Setup.exe program packages contained in the CD provided with the MaxiSys tool kit. The packages include the following applications:

To install the Setup.exe program
1.    Insert the CD into the CD-ROM of the computer. The driver installation wizard will load momentarily.
2.    Click on Next on the welcome page.
3.    Click the Change button, and select a destination folder to install the program, and click Next to continue. Or directly click Next to continue without changing the default installation folder.
4.    Click Install and the Setup.exe program will be installed onto the computer.

3.1 Printing Operation

This section describes how to receive file from the display tablet and perform printing through the computer:

To perform printing through the computer
1.    Install the PC Link (Printing Services program) to the computer.
2.    Make sure the obd2tool.com MS906 tablet is connected to the computer network, either via Wi-Fi or LAN, before printing.
3.    Run the Printing Services program on the computer.
4.    Tap the Print button on the toolbar displayed in various applications of the MaxiSys system. A temporary file will be created and sent to
5.    Click the Printer Server tab on the top of the program interface on the computer, and wait for the printing file to load.
6.    Click the Print button to start printing.

Maxisys Elite Data Manager Operations

The Maxisys Elite Data Manager application is used to store, print, and review the saved files. Most operations are controlled through the toolbar. Selecting the Data Manager application opens the file system menu. Different file types are sorted separately under different options, there are six types of information files to be viewed or played back.

41-1

Operations
The OBD-II scan tool Data Manager Operations are based on toolbar controls, details are explained in the following sections.

Image Files
The Image section is a JPG database containing all captured screenshot images.

41-2

1.  Toolbar Buttons – used to edit, print and delete the image files. See Table 5-1 Toolbar Buttons in JPG Database on page 64 for detailed information.
2.  Main Section – displays the stored images.

41-3

To edit image information
1.  Select Data Manager application from the MaxiSys Job Menu.
2.  Select Image to access the JPG database.
3.  Select an image to display it in full screen.
4.  Tapping the screen once displays the editing toolbar.
5.  Tap the Info button to open a window displaying the image information.
6.  Tap the Edit button on the top right corner of the window. The editing screen displays.
7.  Edit the image information by entering the new file name, and file information.
8.  Tap Done to save the information and exit, or tap Cancel to exit without saving.

To delete selected images
1.  Select Data Manager application from the Autel Scanner MaxiSys Job Menu.
2.  Select Image to access the JPG database.
3.  Tap the Enter Edit button to display the editing toolbar.
4.  Select the images that need to be deleted by tapping the thumbnail images, the selected thumbnail displays a tick icon at the bottom right corner.
5.  Tap the Delete button, and then Delete Selected, now the selected images are deleted.

Autel Maxisys Elite ECU Information

This function retrieves and displays the specific information for the tested control unit, including unit type, version numbers and other specifications. The sample Autel Maxisys Elite ECU Information screen displays as below:

36-1

1.  Diagnostics Toolbar Buttons – see Table 4-2 Diagnostics Toolbar Buttons on page 33 for detailed descriptions of the operations for each button.
2.  Main Section – the left column displays the item names; the right column shows the specifications or descriptions.
3.  Functional Button – In this case, only a Back (or sometimes an ESC) button is available; tap it to exit after viewing.

36-2

Read Codes

This function retrieves and displays the DTCs from the vehicle’s control system. The Read Codes screen varies for each vehicle being tested, on some vehicles, freeze frame data can also be retrieved for viewing. The sample Read Codes screen displays as below:

1.  Diagnostics Toolbar Buttons – see Table 4-2 Diagnostics Toolbar Buttons on page 33 for detailed descriptions of the operations for each button.
2.  Main Section
*   Code Column – displays the retrieved codes from the vehicle.
*   Status Column – indicates the status of the retrieved codes.
*   Description Column – detailed descriptions for the retrieved codes.
*   Snowflake Icon – only displays when freeze frame data is available for viewing; Selecting displays a data screen, which looks very similar to the Read Codes interface, therefore same operation method may be applied.

Erase Codes
After reading the retrieved codes from the vehicle and certain repairs have been carried out, you can decide to erase the codes from the vehicle using this function. Before performing this function, make sure the vehicle’s ignition key is in the ON (RUN) position with the engine off.

To erase codes
1.  Tap Erase Codes from the Function Menu.
2.  A warning message displays to inform you of data loss when this function is applied.
a)  Tap Yes to continue. A confirming screen displays when the operation is successfully done.
b)  Tap No to exit.
3.  Tap ESC on the confirming screen to exit Erase Codes.
4.  Check the Read Codes function again to ensure the operation is successful.
3.  Functional Button – in this case, only a Back (or sometimes an ESC) button is available; tap it to return to the previous screen or exit the function.

Live Data
When this function is selected, the screen displays the data list for the selected module. The Autel Scanner available for any control module vary from one vehicle to another. The parameters display in the order that they are transmitted by the ECM, so expect variation between vehicles. Gesture scrolling allows you to quickly move through the data list. Simply touch the screen and drag your finger up or down to reposition the parameters being displayed if the data covers more than one screen. The figure below shows a typical Live Data screen:
36-3

1.  Diagnostics Toolbar Buttons – tap the drop-down button at the top
center of the screen displays the toolbar buttons. See Table 4-2
Diagnostics Toolbar Buttons on page 33 for detailed descriptions of the
operations for each button.

2.  Main Section
*   Name Column – this column displays the parameter names.
a)  Check Box – tap the check box at the left side of the parameter name to make selection of an item. Tap the check box again to deselect the item.
b)  Drop-down Button – tapping the drop-down button at the right side of the parameter name opens a submenu, which provides various choices for data display mode.
*   Value Column – displays the values of the parameter items.
*   Range Column – displays the minimum and the maximum limit value.
*   Unit Column – displays the unit for the parameter values.
*   To change the Unit mode, tap the Setting button on the top toolbar and select a required mode. See 7.1.1 Unit on page 77 for more information.

3.  Display Mode
There are 4 types of display modes available for data viewing, allowing you to view various types of parameters in the most suitable way for better data check-ups.
Tapping the drop-down button on the right side of the parameter name opens a submenu. There are 4 buttons to configure the data display mode, plus one Help button on the right, tappable when additional information is available for your reference. Each parameter item displays the selected mode independently.
Analog Gauge Mode – displays the parameters in form of an analog meter graph Text Mode – this is the default mode which displays the parameters in texts and shows in list format
NOTE: Reading of status parameters, such as a switch reading, which are mostly in word form, like ON, OFF, ACTIVE, and ABORT, etc., can only be displayed in Text Mode. Whereas reading of value parameters,
such as a sensor reading, can be displayed in text mode and other graph modes.

Waveform Graph Mode – displays the parameters in waveform graphs When displaying this mode, three control buttons will appear on the right side of the parameter item, allowing you to manipulate the display status.
*   Text Button – resumes Text Display Mode
*   Scale Button – changes the scale values, which are displayed below the waveform graph. There are 4 scales available: x1, x2, x4 and x8.
*   Zoom-in Button – tap once to display the selected data graph in full screen
Digital Gauge Mode– displays the parameters in form of a digital gauge graph
Full Screen Display – this option is only available in the waveform graph mode, and mostly used in Graph Merge status for data comparison.
There are three control buttons available on the top right side of the
screen under this mode.
*   Edit Button – tapping this button opens an edit window, on which you can set the waveform color and the line thickness displayed for the selected parameter item.
*   Scale Button – changes the scale values, which are displayed below the waveform graph. There are 4 scales available: x1, x2,x4 and x8.
*   Zoom-out Button – exits full screen display.
*   To edit the waveform color and line thickness in a data graph
1.  Select 1 to 3 parameter items to display in Waveform Graph mode.
2.  Tap the Zoom-in Button on the right to display the data graph in full screen.
3.  Tap the Edit Button, an edit window appears.
4.  Select a parameter item on the left column.
5.  Select a desired sample color from the second column.
6.  Select a desired sample line thickness from the right column.
7.  Repeat step 4-7 to edit the waveform for each parameter item.
8.  Tap Done to save the setting and exit, or tap Cancel to exit without saving.

4.  Functional Buttons
The operations of all the available functional buttons on Live Data screen are described below:
Back – returns you to the previous screen or exit the function.
Record – starts recording the retrieved live data; the recorded data is then stored as a video clip in the Data Manager application for future reviews. This function could be triggered automatically at preset threshold value or manually as you choose, and the triggering mode and record duration can be configured in the Setting mode of Live Data.
Freeze – displays the retrieved data in freeze mode.
*   Previous Frame – Moves to the previous frame in the freeze data.
*   Next Frame – Moves to the next frame in the freeze data.
*   Resume – this button appears when the Record or Freeze function is applied. Tapping this button stops data recording, or exit freeze data mode, and resumes normal data display mode.
*   Flag – this button appears when the Record function is applied. Tapping this button sets flags for the recorded data at points wherever you choose, when playing back the recorded video clip later in Data Manager, the
preset flag will enable a popup to allow input of text to take notes.

*  Clear Data –tapping which clears all previously retrieved parameter values at a cutting point whenever you choose.
*  To Top – moves a selected data item to the top of the list.
*  Graph Merge – tap this button to merge selected data graphs (for Waveform Graph Mode only). This function is very useful when making comparison for different parameters.
NOTE: This mode supports Graph Merge for 2 to 3 parameter items only, so select no less than 2 or more than 3 items each time when making graph merge.
*   To cancel Graph Merge mode, tap the drop-down button on the right side of the parameter name, and select a data display mode. Show Selected/Show All – tap this option to exchange between the two options; one displays the selected parameter items, the other displays all the available items.

Setting – tapping this button opens a setting screen, which allows you to set the trigger mode, recording duration, and various threshold values for data recording, and make other controls.

36-4

There are 4 navigation buttons on top of the Setting mode screen.
*   Range Button – displays the configuration screen on which you can set the threshold values, an upper limit and a lower limit, for triggering the buzzer alarm. This function is only applied to the Waveform Graph display mode.
a)  MIN – tapping which opens a virtual keyboard, allows you to enter the required lower limit value
b)  MAX – tapping which opens a virtual keyboard, allows you to enter the required upper limit value
c)  Buzzer Alarm – switches the alarm on and off. The alarm function makes a beep sound as a reminder whenever the data reading reaches the preset minimum or maximum point

 To set threshold limits for the parameter values
1.  Tap the Setting functional button at the bottom of the Live Data screen.
2.  Tap the Range navigation button.
3.  Select a parameter item on the left column, or enter the item name in the Search bar.
4.  Tap on the right side of the MIN button, and enter the required minimum value.
5.  Tap on the right side of the MAX button, and enter the required maximum value.
6.  Tap the ON/OFF button on the right side of the Buzzer Alarm button to turn it on or off.
7.  Tap Done to save the setting and return to the Live Data screen; or tap Cancel to exit without saving.
If the threshold limits are successfully set, two horizontal lines now appear on each of the data graphs (when Waveform Graph Mode is applied) to indicate the alarming point. The threshold lines are shown in different colors than the waveform of the parameters for distinction.
*   Record Button – displays the configuration screen for Record Setting, on which you can set the trigger type, duration and trigger point for the data recording function.
a)  Trigger Type – sets the trigger mode for data recording, mainly of two kinds: Manual and Auto. There are four options available:
1)  Manual – allows you to manually start and stop data recording
2)  DTC – auto triggers data recording when any DTC is detected
3)  DTC Check Mode – auto triggers data recording when certain pre-selected DTC types are detected
4)  Parameter – auto triggers data recording when any parameter value reaches the preset threshold
b)  Duration – sets the recording time (for Auto trigger mode only)
c)  Trigger Point – reserves a relative percentage of a record length before the data recording start point for reference (for Auto trigger mode only)
*   To perform setting for live data record
1.  Tap the Setting functional button at the bottom of the Live Data screen.
2.  Tap the Record navigation button.
3.  Tap the  ○> button on the right of Trigger Type bar and select the required trigger mode.
4.  Tap the  ○> button on the right of Duration bar and select a
length of time.
5.  Tap the  ○> button on the right of Trigger Point bar and select a relative percentage of a record length to be reserved before the data recording start point.
6.  Tap Done to save the setting and return to the Live Data screen; or tap Cancel to cancel without saving and exit Setting.
*   Done Button – confirms and saves the setting, and returns you to the Live Data screen.
*   Cancel Button – cancel the setting operation, and returns you to the Live Data screen

Active Test
The Active Test function is used to access vehicle-specific subsystem and component tests. Available test vary by manufacturer, year, and model, and only the available tests display in the menu. During an active test, the tester outputs commands to the ECU in order to drive the actuators. This test determines the integrity of the system or parts by reading the engine ECU data, or by monitoring the operation of the actuators, such as switching a solenoid, relay, or switch, between two operating states.
Selecting Active Test opens a menu of test options that varies by make and model. Selecting a menu option activates the test. Follow all screen instructions while performing tests. How and what information is presented on the screen varies according to the type of test being performed. Some toggle and variable control tests display Active Test Controls at the top of the screen with data stream information below, or vice versa.

36-5
The functional buttons at the lower right corner of the Active Test screen manipulate the test signals. The operational instructions are displayed on the main section of the test screen. Simply follow the on-screen instructions and make appropriate selections to complete the tests. Each time when an operation is successfully executed, message such as ―Command Finished‖,―Activation Successful‖, or something similar displays.

Tap the ESC functional button to exit the test when finished.

 

This article is publiced by www.obd2tool.com

Autel MaxiSYS MS906 Diagnostic Scanner

14-1

Autel is a leading company experienced in producing professional diagnostic tools, equipment and accessories in the automotive aftermarket. Focused on the orientation of “value innovation and assiduous pursuit”, Autel has always adhered to deliver easier diagnostic solutions and long-time value to customers worldwide.

MaxiSYS MS906 is an advanced diagnostic tool developed for mechanics looking for a scanner with ultra-convenient and modern design while delivering ultimate performance. Featuring the Samsung 6-core processor, an 8.0 inch LED capacitive touch screen, Android multitasking operating system and the exceptional OE-level diagnostics, this diagnostic scanner MS906 is absolutely an ideal solution to manage your repair jobs smartly and conveniently with greater integration.

14-2

ECU Coding & Special Functions
The scan tool provides you with quick access to all vehicle systems for various service and maintenance performances as followings.
1. Oil Reset Service to reset service mileage and service intervals for the Engine Oil Life system;
2. TPMS Service to look up the tire sensor IDs from ECU, as well as to perform TPMS programming and reset procedures after sensor replacements;
3. EPB Service to deactivate and activate the brake control system, assist with brake fluid control, open and close brake pads, and set brakes after disc or pad replacement, etc.;
4. ABS/SRS Services to perform bi-directional tests to check the operating conditions of ABS and SRS, such as Automated Bleeding, Pump Motor Test, and checking Module information, etc.;
5. SAS Service to perform calibration for the Steering Angle Sensor, and clear fault memory;
6. DPF Regeneration Service to clear the blockage through continuous burning of the particulate matter captured in the DPF filter.

14-3
Complete Diagnostic Functions for All Systems
With a wide range of capabilities, the MS906 will let you get more repair work done quickly and easily. Look what this diagnostic scan tool will bring to you.
Perform Complete Diagnostic Functions
1. Retrieve ECU information of tested control units including unit type, version numbers and other specifications;
2. Read all kinds of DTCs from vehicle’s control systems to locate problem areas, and offer possible solutions;
3. Erase the codes easily after DTCs retrieving and certain repairs have been carried out;
4. Live data of each parameter item displayed in analog, text, waveform graph, digital, or full screen display modes;
5. Active test used to access vehicle-specific subsystem and component tests.
In All Vehicle Systems on the ECUs
The diagnostic tool can access to ALL vehicle systems and subsystems, such as Body, Chassis,

14-4

Extension Usage
Powertrain, Network and etc., to perform a comprehensive scanning on ECUs to locate fault systems and retrieve DTCs.

Optional Accessories for Maximized Advantage of this Scanner
To help you get the most from MS906, there are many optional accessories to work with the diagnostic tablet. This diagnostic scanner offers you more potential functions of Autel TPMS Tool when working with the TPMS diagnostic tool MaxiTPMS TS401 from Autel.

Best Possible Hardware

The considerate grease and water resistant design are suitable for garage works; Samsung 6-Core processor operates quickly and reliably; 8-megapixel rear camera with autofocus and flashlight offers a good vision; 8.0” 1024×768 LED-backlit touchscreen works well for intuitive results display; 32GB SSD for better performance; 5000mAH lithium-polymer battery for flexible anytime use; Android Operating System lets you finish multitask in powerful yet simple ways.

14-5

Wide Vehicle Coverage

This OBD2 scan tool works on more than 80 US, Asian and European vehicle makes, and well combines with up to 12 kinds of adapters included in package. Even OBD-I complaint vehicles are perfectly supported by this diagnostic scanner when connecting via these adapters. Get one diagnostic scanner, and you can diagnose much more vehicles than using other diagnostic scan tools.

14-6

Convenient Information Management

MaxiFix, an online database to find diagnostic tips and proven filed fixes; Shop Manager is to well manage the workshop and customer information records, and those test vehicle history records; Data Manager to store, print, and review the saved files in different types; Data Logging to submit help requests for 48-hour replies; Notification Center to receive the latest service information like software update notification.

14-7 14-8

Package Contents

14-9