Possible to Program a Used Nissan ECM with Diagun IV?

August 6, 2019 Eva Launch X431 Tools 0

Possible to Program a Used Nissan ECM with Diagun IV?

As titled, possible to program a used Nissan ECM by using Launch X431 Diagun IV OBD2 diagnostic scanner?
A: Yes. Check step-by-step guide below:

Procedure:
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-1 Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-2

Connection Diagun IV with vehicle via DBscar Bluetooth connector
(Note: pocket juice is a portable charger.)
Run Diagun IV application
Select Diagnose function->Asian->Nissan
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-3 Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-4
connecting bluetooth
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-5

This vehicle has a 16-PIN standard connector
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-6

Reads VIN
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-7

Choose Maintenance function->NATS (Nissan Anti-theft system)-> Manual selection test->After replacing or installing operation->Replace ECM (Used Part)
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-8
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-9
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-10
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-11
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-12

This procedure erase all registered keys. Therefore, all of the customer’s keys should be obtained before starting this procedure.
Press OK to continue.

Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-14

Follow procedure below to operate:
1. Get Immobilizer code (PIN) for initialization from the following
encrypted PIN (5 or 12 digits)
Encrypted PIN
(5 or 12 digits): 1288a
2. Input PIN for initialization into the following input column
IMMO code for initialization
Old Password (Before 2010): 5521
New Password (After 2010): 3521
3.Press Next. The system starts communication with the vehicle.

Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-15

This is an old model, so here we enter old password

Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-16
Operate according to following procedure:
1. Insert ignition key into ignition key cylinder and turn on ignition switch.
After performing this operation. The system automatically proceeds to initialization ECU.
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-17

Perform key registration.
1. Remove inserted ignition key
2.Insert unregistered ignition key into ignition and turn to ON position. and then wait for 5 seconds or more.
3. Check the security indicator flashes for 5 times
4. Turn ignition switch to OFF position. Remove ignition key and wait for 3s or more.
5. A Maximum of 5 ignition keys can be registered by repeating procedure from step 2 to step 4 using unregistered ignition keys.  Press Next to finish key registration mode.
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-18

Program used ECM finished. Now you need to register VIN with ECM.
Go to System Scan->ECM (Engine Control Module)->Special Function->VIN Registration
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-19
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-20
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-21
Possible-to-Program-a-Used-Nissan-ECM-with-Diagun-IV-22

Turn ignition switch to ON position but don’t start engine during the procedure.
Follow Diagun 4 scanner prompts until success.

Related posts:

  1. Program Toyota Avalon 2014 All Keys Lost with Tango & Lonsdor 518ISE
  2. CGDI MB Program Old Benz K-line w202 w208 w210 Key via OBD
  3. Lonsdor K518 Program Renault All Key Lost
  4. Why 2017 Launch X431 Diagun IV can replace Diagun III / X431 IV?

Be the first to comment

Leave a Reply

Your email address will not be published.


*